degree of cure
英 [dɪˈɡriː ɒv kjʊə(r)]
美 [dɪˈɡriː əv kjʊr]
硫化程度；固化程度
双语例句
- Relation of the Property of a Low Viscosity Epoxy Resin Casting Matrix to Its Degree of Cure
低粘度环氧树脂浇铸体性能与固化度的关系 - Furthermore, the phenol could increase the maximum degree of cure of modified resin.
而苯酚的加入可明显提高改性体系的最大固化度。 - Simulation and experiment of the degree of cure during CFRP pultrusion
CFRP拉挤工艺过程固化度数值模拟与实验 - Objective To ascertain the range and harm degree of the area of Endemic Fluorosis in liang he and provide scientific basic to enact countermeasure of prevention and cure.
目的查明梁河县地氟病区范围及危害程度，为制定防治对策提供科学依据。 - Does cervical vertebra physiology degree of curve unexpected turn of events accompany method to oppose the wrong symptom origin, clinical manifestation and cure straightly?
颈椎生理曲度变直伴反曲的症状起因、临床表现及治疗方法？ - The degree of cure and temperature are coupled during the pultrusion of carbon fiber reinforced plastics ( CFRP).
碳纤维增强塑料（CFRP）拉挤成型过程中固化度和温度变化为强耦合关系。 - Measurement of degree of cure of FBE coatings& solvent extraction method
环氧粉末涂料固化程度的表征-溶剂萃取法的建立 - The degree of cure ( DOC) of a new type of epoxy/ dicyandiamide powder coatings was detected by using solvent extraction on the free film cured at temperatures from 160 ℃ to 230 ℃ for different time and the kinetic process was analyzed.
用丁酮作萃取溶剂，研究了环氧/双氰胺粉末涂层自由膜在160～230℃温度下经不同时间固化后的萃取固化度，分析了涂膜固化反应的动力学过程。 - Based on the thermal conduct theory and cure kinetics, the history of cure temperature and degree of cure was investigated for the orthotropic laminate during curing.
根据热传导和固化动力学理论，采用三维有限元方法，对正交各向异性复合材料层合板固化过程的温度和固化度历程及其变化规律进行数值模拟研究。 - Calculation analysis for degree of cure of tire
轮胎硫化程度的计算分析 - A description was given to the definition of curing and cure degree of unsaturated polyester resin, to the factors affecting the cure degree and to the ways to determine the cure degree.
本文阐述UPR固化和固化程度的含义、影响固化程度的因素和评定固化程度的方法。 - The corelation about degree of cure profiles and temperature of composites in the pultrusion die is discussed.
给出了碳纤维抽油杆复合材料在拉挤模具内温度和固化度变化的规律。 - The temperature and degree of cure were chosen as two additional degrees of nodes in FEM models, and the coupling of them was taken into account.
在有限元分析中节点自由度为温度和固化度，考虑了两者之间的耦合作用。 - It is also the mainly direction of analysis and design of materials in the future. The property of pultrusion production depends on the degree of cure.
这对于节约成本、提高劳动生产率、缩短产品研制周期等方面具有十分积极的意义，也是未来材料分析和设计的发展趋势。 - The cure kinetics model is based on Kamal's model, and the degree of the resin cure as a function of temperature and time. This improved mixing dielectric model yields an excellent fit to measured data.
树脂的固化模型利用了Kamal提出的固化动力学方程，将固化度取为时间和温度的函数。 - The test method for properties of UVcuring art adhesives including viscosity, chrominance, refractive index and degree of cure ect.
阐述了紫外光固化艺术胶的性能（包括粘度、色度、折光度、固化程度等）测试方法。 - Through numerical examples, the influence of the temperature boundary conditions, the thickness of the plate and the heating rates on the distribution of the temperature and the degree of cure of the laminates are analysed and discussed.
通过算例，分析和讨论了层合板的温度边界条件，板厚度以及升温速率对层合板内温度和固化度分布的影响。 - Then, through Fourier Transform Infrared spectrometer ( FTIR), we discussed the change of the final degree of cure of the cured resin with different initiators system, and found that the cooperated initiators system can effectively increase the final degree of cure even in low content.
然后通过红外光谱（FTIR）分析了树脂在不同固化剂体系下的固化度，认为采用不同活性的联用固化剂体系可以在相对较少的用量下有效地提高树脂固化度。 - On curing phase separation occurs to form two phase structures. The degree of phase separation depends upon the cure conditions.
共混物在固化过程中发生相分离而形成两相结构，相分离程度与固化条件有关。 - The effects of processing parameters including pulling speed, die wall temperature, die thickness and initial conditions on the profile of degree of cure and temperature in the die is discussed.
使用开发的计算机程序详细的探讨了各种拉挤工艺参数（模具温度，模具厚度，拉挤速度，初始温度等）对模具内温度和固化度分布的影响。 - Influence of degree of cure and cure shrinkage on the finial deformation of the unsymmetric composite laminates
固化度与固化收缩对非对称复合材料层合板固化变形的影响 - The TB patients both Sichuan Province and Anhui Province had a serous degree delay in the course of diagnosis and treatment, which influence upon cure rate of them, and drug resistance TB was one of the important cause inducing the failure of treatment.
两省的结核病患者诊断和治疗过程中延误状况严重，影响结核病的治愈率，耐药结核是导致当地治疗失败的一个重要原因。 - The results indicated that even in the heat under the certain time can be guaranteed the degree of cure when the content of curing agent was 1%.
结果表明：固化剂加入量为1%时，在放热均匀的前提下，可保证一定时间下的固化度。